TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT Process) certain hazardous substances in electrical and electronic equipment. C Lot No. . this document, the specifications, the data sheets and application notes. CY Bipolar Transistors – BJT are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for CY Bipolar Transistors – BJT. COR NTE Equvilent NTE31 TRANSISTOR NPN SILICON V 1AMP GIANT TO CASE TV SOUND OUTPUT COMP’L TO NTE NTE Data Sheet.

Author: Gardagami Dozahn
Country: Honduras
Language: English (Spanish)
Genre: Business
Published (Last): 14 December 2012
Pages: 51
PDF File Size: 14.71 Mb
ePub File Size: 10.45 Mb
ISBN: 809-9-14107-178-7
Downloads: 66993
Price: Free* [*Free Regsitration Required]
Uploader: Maura


Please use these products in this document in compliance with all applicable laws and regulations. Ty for your attention.

Posted by santonel in forum: Mar 2, 3. Mar 2, 5. Transistoe use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Mar 2, 2. I have a 12V power supply and a square wave V as a input on the base.

The C xstr has a minimum gain of Nevertheless, semiconductor devices xatasheet general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. Solar Powered Security Light In this teardown, dztasheet will look at the internals of a motion-activated light which contains its own solar charging system. Mar 3, Unintended Usage include atomic energy control instruments, airplane or.

Similar to what veritas has explained: May 16, 5, 8. No, create an account now. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.


I am checking with my tester and there is never current through R1 voltage between sides of it it’s always 0 no matter the input, so i wander how can the current reach the base?? The transistor can also be checked by removing it from the circuit and using an ohm-meter: If you’re using the transistor purely as a switch, that means you want to saturate the output, or try to cause more current to flow from collector to emitter than your current limiting resistor will allow.

C datasheet, C datasheets, manuals for C electornic semiconductor part

Do you already have an account? The attached simulation diagram “sim” shows a circuit using the values I derived, the results are in the “res” file and “zoom” shows the low output relative to ground a few tenths of a volt as should be expected. Toshiba assumes no liability for damage or losses. The resistor can be checked by removing it from the circuit and using an ohm-meter. transixtor

C2383 NPN transistor.. helpme with R

With 0V-4V drive 1KHz. Using continuously under heavy loads e.

Feb 7, 0. You May Also Like: I guess I attempted to establish what ratasheet was talking about in my first response. Or even as I tried from beginning 4.

V CEO V. Mar 2, 3 0.

C Datasheet, PDF – Alldatasheet

Mar 2, 4. Aug 8, Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion translstor instruments, medical instruments, all types of safety devices, etc.


Without a schematic, “R1” and “R2” are meaningless labels.

I’m starting to think that this bjt is burned. This is how I envisioned the circuit: It is the responsibility of the buyer, transjstor utilizing TOSHIBA products, to comply with the standards of daasheet in making a safe design for the entire system, and to avoid situations in which datashheet malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property.

Then a darlington driver transistor must replace the ordinary transistor. Mar 2, 1. Dec 20, 10, 1, No license is granted by implication or otherwise under any patents or other rights of. Yes, my password is: If you don’t care whether the load you’re driving is sinking mA or dagasheet, and it’s only important that it doesn’t exceed a maximum of mA, just choose R2 such that no more than mA can flow through it. It is very unlikely that the resistor is bad – they typically get fat and brown when they open.

We don’t know if the 5V signal is still 5V when loaded. The bjt is of course in common emitter configuration.